Diodes Incorporated
Imej mungkin representasi.
Lihat spesifikasi untuk butiran produk.
FZT955TC
Lihat Butiran Helaian data

FZT955TC

Introduction

The FZT955TC is a high-performance NPN silicon transistor designed for various electronic applications. This entry provides an overview of the product, including its category, use, characteristics, packaging, specifications, pin configuration, functional features, advantages and disadvantages, working principles, application field plans, and alternative models.

Product Overview

  • Category: Electronic Components
  • Use: Amplification and Switching in Electronic Circuits
  • Characteristics: High Voltage and Current Capability, Low Saturation Voltage
  • Package: SOT-223
  • Essence: Power Transistor
  • Packaging/Quantity: Tape and Reel, 3000 units per reel

Specifications

  • Collector-Emitter Voltage (VCEO): 100V
  • Collector Current (IC): 3A
  • Power Dissipation (Ptot): 2.25W
  • Transition Frequency (ft): 150MHz
  • HFE: 40 to 400

Detailed Pin Configuration

The FZT955TC has a standard SOT-223 package with three pins: 1. Emitter (E) 2. Base (B) 3. Collector (C)

Functional Features

  • High Voltage Capability
  • Low Saturation Voltage
  • Fast Switching Speed
  • High Current Gain

Advantages and Disadvantages

Advantages

  • Suitable for High Power Applications
  • Low Saturation Voltage Enhances Efficiency
  • Wide Range of Current Gain

Disadvantages

  • Relatively Higher Transition Frequency
  • Sensitive to Overcurrent Conditions

Working Principles

The FZT955TC operates based on the principles of bipolar junction transistors, utilizing the control of current flow between its terminals to amplify or switch electronic signals.

Application Field Plans

The FZT955TC is ideal for use in the following applications: - Power Supplies - Motor Control - Audio Amplifiers - LED Drivers - Switching Circuits

Alternative Models

For users seeking alternatives, the following models can be considered: - FZT855TC - FZT1055TC - FZT1155TC

In conclusion, the FZT955TC offers high performance and versatility in electronic applications, making it a valuable component for various circuit designs.

[Word Count: 314]

Senaraikan 10 soalan dan jawapan biasa yang berkaitan dengan aplikasi FZT955TC dalam penyelesaian teknikal

  1. What is the FZT955TC transistor used for?

    • The FZT955TC is a high-gain, low-saturation voltage NPN transistor commonly used in switching applications and amplification circuits.

  2. What are the key specifications of the FZT955TC transistor?

    • The FZT955TC has a maximum collector current of 3A, a collector-emitter voltage of 100V, and a DC current gain (hFE) of 40 to 400.

  3. How can I use the FZT955TC in a switching application?

    • The FZT955TC can be used in switching applications by connecting it as a common-emitter amplifier with appropriate base current limiting resistor and load.

  4. Can the FZT955TC be used in audio amplifier circuits?

    • Yes, the FZT955TC can be used in small signal audio amplifier circuits due to its high gain and low saturation voltage.

  5. What are the typical operating conditions for the FZT955TC?

    • The FZT955TC operates within a temperature range of -55°C to 150°C and is suitable for general purpose electronic applications.

  6. Is the FZT955TC suitable for driving inductive loads?

    • Yes, the FZT955TC can be used to drive inductive loads such as relays and small motors when paired with appropriate protection diodes.

  7. Can the FZT955TC be used in voltage regulator circuits?

    • While the FZT955TC is not typically used in voltage regulator circuits, it can be employed in pre-regulator or driver stages of certain power supply designs.

  8. What are the recommended soldering and handling precautions for the FZT955TC?

    • It is recommended to follow standard ESD (electrostatic discharge) handling procedures and to observe the specified soldering temperature and duration to avoid damaging the transistor.

  9. Are there any common failure modes associated with the FZT955TC?

    • Common failure modes include thermal overstress, overvoltage breakdown, and excessive base current leading to saturation.

  10. Where can I find detailed application notes for using the FZT955TC in technical solutions?

    • Detailed application notes for the FZT955TC can be found in the manufacturer's datasheet, as well as in various electronics engineering resources and forums.