Infineon Technologies
Imej mungkin representasi.
Lihat spesifikasi untuk butiran produk.
IPI25N06S3-25
Lihat Butiran Helaian data

IPI25N06S3-25

Product Overview

Category

The IPI25N06S3-25 belongs to the category of power MOSFETs.

Use

It is commonly used in power supply applications, motor control, and other high-power switching circuits.

Characteristics

  • High voltage capability
  • Low on-resistance
  • Fast switching speed
  • Low gate charge

Package

The IPI25N06S3-25 is typically available in a TO-220 package.

Essence

This MOSFET is essential for efficient power management and control in various electronic systems.

Packaging/Quantity

It is usually packaged in reels or tubes, with quantities varying based on manufacturer specifications.

Specifications

  • Drain-Source Voltage (VDS): 60V
  • Continuous Drain Current (ID): 25A
  • On-Resistance (RDS(on)): 0.025 ohms
  • Power Dissipation (PD): 150W
  • Gate-Source Voltage (VGS): ±20V
  • Operating Temperature Range: -55°C to 175°C

Detailed Pin Configuration

The IPI25N06S3-25 has a standard pin configuration with three pins: gate, drain, and source. The pinout is as follows: - Pin 1 (Gate) - Pin 2 (Drain) - Pin 3 (Source)

Functional Features

  • High voltage capability allows for use in various power applications.
  • Low on-resistance minimizes power loss and improves efficiency.
  • Fast switching speed enables rapid response in switching circuits.

Advantages

  • Excellent power handling capabilities
  • Low on-resistance for reduced power dissipation
  • Fast switching speed for improved efficiency

Disadvantages

  • Higher cost compared to standard MOSFETs
  • Sensitive to static discharge if mishandled

Working Principles

The IPI25N06S3-25 operates based on the principles of field-effect transistors, where the gate voltage controls the flow of current between the drain and source terminals. When the gate-source voltage is applied, it creates an electric field that modulates the conductivity of the channel, allowing for efficient power control.

Detailed Application Field Plans

The IPI25N06S3-25 is widely used in the following applications: - Switching power supplies - Motor control systems - Inverters and converters - Audio amplifiers - LED lighting systems

Detailed and Complete Alternative Models

Some alternative models to the IPI25N06S3-25 include: - IRF3205 - FDP8878 - STP80NF55-06

In conclusion, the IPI25N06S3-25 power MOSFET offers high-performance characteristics suitable for a wide range of power management and control applications, despite its higher cost and sensitivity to static discharge.

[Word Count: 398]

Senaraikan 10 soalan dan jawapan biasa yang berkaitan dengan aplikasi IPI25N06S3-25 dalam penyelesaian teknikal

  1. What is the IPI25N06S3-25?

    • The IPI25N06S3-25 is a power MOSFET transistor designed for high efficiency and high power density applications.

  2. What are the key features of the IPI25N06S3-25?

    • The key features include a low on-state resistance, fast switching speed, and a rugged design suitable for demanding applications.

  3. What are the typical applications for the IPI25N06S3-25?

    • Typical applications include motor control, power supplies, inverters, and other high-power switching circuits.

  4. What is the maximum voltage and current rating for the IPI25N06S3-25?

    • The IPI25N06S3-25 has a maximum voltage rating of 60V and a continuous drain current rating of 25A.

  5. What is the thermal performance of the IPI25N06S3-25?

    • The device is designed with low thermal resistance to ensure efficient heat dissipation in high-power applications.

  6. Does the IPI25N06S3-25 require any special driving considerations?

    • It is recommended to use proper gate drive circuitry to ensure optimal performance and reliability.

  7. Can the IPI25N06S3-25 be used in automotive applications?

    • Yes, the IPI25N06S3-25 is suitable for automotive applications where high power and efficiency are required.

  8. Are there any specific layout considerations when using the IPI25N06S3-25?

    • Proper PCB layout and thermal management are important to maximize the performance and reliability of the device.

  9. What are the environmental and compliance specifications for the IPI25N06S3-25?

    • The device complies with industry standards for environmental protection and is designed for RoHS compliance.

  10. Where can I find detailed technical documentation for the IPI25N06S3-25?

    • Detailed technical information, including datasheets and application notes, can be found on the manufacturer's website or through authorized distributors.