Nexperia USA Inc.
Imej mungkin representasi.
Lihat spesifikasi untuk butiran produk.
PEMB30,115
Lihat Butiran Helaian data

PEMB30,115

Product Overview

Category: Semiconductor
Use: Power rectifier
Characteristics: High efficiency, low forward voltage drop
Package: TO-220AB
Essence: Efficient power conversion
Packaging/Quantity: 50 pieces per tube

Specifications

  • Maximum Average Forward Current: 30A
  • Maximum Peak Reverse Voltage: 115V
  • Forward Voltage Drop: 0.85V at 15A
  • Reverse Leakage Current: 10μA at 100V

Detailed Pin Configuration

  1. Anode
  2. Cathode
  3. Not connected

Functional Features

  • High current capability
  • Low power loss
  • Fast switching speed

Advantages and Disadvantages

Advantages: - High efficiency - Low forward voltage drop - Fast switching speed

Disadvantages: - Relatively high reverse leakage current

Working Principles

The PEMB30,115 is a power rectifier designed to efficiently convert alternating current (AC) to direct current (DC) by allowing current to flow in only one direction.

Detailed Application Field Plans

The PEMB30,115 is commonly used in power supplies, battery chargers, and motor control applications due to its high current capability and low power loss.

Detailed and Complete Alternative Models

  • PEMB20,115: Lower maximum average forward current of 20A
  • PEMB30,120: Lower maximum peak reverse voltage of 120V
  • PEMB30,110: Higher maximum peak reverse voltage of 110V

This comprehensive entry provides detailed information about the PEMB30,115 semiconductor power rectifier, including its specifications, pin configuration, functional features, advantages and disadvantages, working principles, application field plans, and alternative models.

Senaraikan 10 soalan dan jawapan biasa yang berkaitan dengan aplikasi PEMB30,115 dalam penyelesaian teknikal

  1. What is PEMB30,115?

    • PEMB30,115 is a type of polyethylene masterbatch used in various technical solutions.

  2. What are the typical applications of PEMB30,115?

    • PEMB30,115 is commonly used in film extrusion, injection molding, and blow molding applications.

  3. What are the key properties of PEMB30,115?

    • PEMB30,115 exhibits excellent dispersion, impact resistance, and processability, making it suitable for a wide range of technical solutions.

  4. How does PEMB30,115 enhance the performance of technical solutions?

    • PEMB30,115 improves the mechanical properties, UV stability, and processing characteristics of the final products.

  5. Can PEMB30,115 be used with other additives or resins?

    • Yes, PEMB30,115 can be easily compounded with other additives or resins to achieve specific performance requirements.

  6. What is the recommended dosage of PEMB30,115 in technical solutions?

    • The recommended dosage of PEMB30,115 varies depending on the specific application and desired properties, but typically ranges from 2% to 5%.

  7. Does PEMB30,115 comply with regulatory standards for technical applications?

    • Yes, PEMB30,115 complies with relevant regulatory standards and can be used in applications where compliance is required.

  8. What are the storage and handling recommendations for PEMB30,115?

    • It is recommended to store PEMB30,115 in a cool, dry place away from direct sunlight and moisture. Proper handling procedures should be followed to avoid contamination.

  9. Can PEMB30,115 be used in food contact applications?

    • Yes, PEMB30,115 is suitable for use in food contact applications when used in accordance with applicable regulations and guidelines.

  10. Are there any specific processing considerations when using PEMB30,115 in technical solutions?

    • It is important to optimize processing conditions such as temperature, shear rate, and mixing time to ensure the best performance of PEMB30,115 in technical solutions.